SMW-AUTOBLOK - Полный каталог оснастки - 2010 EN
для размещения заказа - smwautoblok@smwautoblok.ru
TSF-CP TSR-CP Compensating pull-down chucks 170 - 650 mm
Compensating Compensating active pull-down
Floating jaws Rigid jaws tongue & groove
3 jaws
Application/customer benets
s #LAMPING OF SHAFTS OR CHUCK PARTS WHERE THE REFERENCE IS NOT THE OD
but a center or a centering dia.
s ! CENTER POINT OR A CENTERING INSERT WILL CENTER THE WORKPIECES AND THE JAWS WILL
clamp compensating and actively pull the workpiece down to the datum.
TSF-CP: Compensating clamping with active pull down and oating base jaws.
TSR-CP: Compensating clamping with active pull down and rigid base jaws.
Technical features s TONGUE GROOVE BASE JAWS
s PERMANENT GREASE LUBRICATION
s ACTIVE PULL
DOWN s prooine® chucks = fully sealed – low
s COMPENSATING CLAMPING MAINTENANCE
s CENTRIFUGAL FORCE COMPENSATION
s CENTRAL BORE FOR COOLANT ANDOR AIR
Standard equipment Ordering example
3-jaw-chuck TSF-CP 210/A6
mounting bolts and grease gun or TSR-CP-315/Z220
TSF-CP/TSR-CP TSF-CP/TSR-CP
A
Principle of function: A
1 compensating pre-clamping - 2 active pull-down -
The workpiece is actively pulled down to the center point. The
3 clamping tailstock just supplies the necessary force to support the work-
piece. The result is an exact cylindrial and straight workpiece.
Non active pull down compensating chuck TSF-CP TSR-CP
The workpiece is lifted by the jaws from the center point. oating jaws rigid jaws
When a higher tailstock force is applied for compensation, the
workpiece will be bent.
Technical data deg. TSF-CP 170 TSF-CP 210 TSF-CP 250 TSF-CP 315 TSF-CP 400 TSF-CP 530 TSF-CP 650
mm TSR-CP 170 TSR-CP 210 TSR-CP 250 TSR-CP 315 TSR-CP 400 TSR-CP 530 TSR-CP 650
SMW-AUTOBLOK Type mm
mm 5.2° 5.2° 4.9° 4.9° 4.7° 4.7° 5°
Angular jaw stroke mm 5.3 6.3 7 7 7.5 7.5 9.8
Radial jaw stroke at distance h kN 0.1 0.1 0.1 0.1 0.2 0.2 0.4
Pull down movement (standard) kN 21 25 25 25 30 30 32
Axial piston stroke r.p.m. ±1 ±1.5 ±1.5 ±1.5 ±3
Compensation (on the dia.) at distance h kg 18 25 ±2.5 ±2.5 50 60 100
Max. draw pull kg·m2 44 60 40 40 120 150 180
Max. gripping force at distance h 5000 4500 96 96 2200 1800 1600
Max. speed* 15 27 3800 3000 115 196 386
Mass (plain back without top jaws) 0.06 0.16 41 66 2.3 7 21
Moment of inertia (m·r2) 0.34 0.83
Recommended actuating cylinders SIN-S 85 SIN-S 100 SIN-S 125 SIN-S 125 SIN-S 150 SIN-S 150-175 SIN-S 150-175-200
*The above maximum speed is allowed with standard mass/height top jaws and applying
the full draw pull only. For more informations please contact SMW-AUTOBLOK.
Page 288 Page 282 Page 197
118 SMW-AUTOBLOK smwautoblok@smwautoblok.ru www.smwautoblok.ru